EXTERNAL OBSERVATIONS:
1.0 Straight Pipe Runs, Expansion Joints, Elbows, Reducers and Tees, including where Pipe Rests on Supports:
S/N
Action
Observations
Observation Images
1.1.1
No image(s) found...
1.1.2
No image(s) found...
1.1.3
No image(s) found...
1.2. Branch Connections, Including Reinforcement Pad
S/N
Action
Observations
Observation Images
1.2.1
No image(s) found...
1.2.2
No image(s) found...
1.3. Small Piping Takeoffs (Valves and Piping) Including Gussets
S/N
Action
Observations
Observation Images
1.3.1
No image(s) found...
1.3.2
No image(s) found...
1.4: Flanges and Associated Hardware
S/N
Action
Observations
Observation Images
1.4.1
No image(s) found...
1.4.2
No image(s) found...
1.4.3
No image(s) found...
1.5. Insulation/Weatherproofing/Jacketing:
S/N
Action
Observations
Observation Images
1.5.1
No image(s) found...
1.6. Dead Legs
S/N
Action
Observations
Observation Images
1.6.1
No image(s) found...
1.7. Filter, Strainer, etc:
S/N
Action
Observations
Observation Images
1.7.1
Inspect for signs of leakage, mechanical damage, coating failure, corrosion or cracks in welds
No image(s) found...
1.7.2
Verify that the device is properly supported to prevent excessive loading on piping.
No image(s) found...
1.8. Anchors/Restraints/Guides/Spring Hangers / Support Roods Including Pipe Clamps
S/N
Action
Observations
Observation Images
1.8.1
Inspect for mechanical damage, cracks in attachment welds, corrosion and distortion
No image(s) found...
1.8.2
Verity that spring hangers are free to move and not bottomed or topped out of their travel range.
No image(s) found...
1.8.3
Note any missing hangers or supports.
No image(s) found...
S/N
Action
Observations
Observation Images
1.9.1
Inspect for signs of leakage especially from weep holes.
No image(s) found...
1.9.2
Inspect for mechanical damage and cracks in the welds attaching it to the process piping
No image(s) found...
1.9.3
Inspect for coating failure and corrosion especially on hard to reach areas that may not have been properly coated.
No image(s) found...
1.9.4
Verify that dummy legs have unobstructed weep holes at the bottom
No image(s) found...
1.9.5
Inspect internal of open ended supports and underside of process piping through the open end for corrosion
No image(s) found...
2.0 . Safety Relief Device and Associated Piping
S/N
Action
Observations
Observation Images
2.1.1
Verify that the inlet and outlet block valves are carsealed open
No image(s) found...
2.1.2
Verify that atmospheric vents have weep holes and are free of obstructions
No image(s) found...
2.1.3
Identify inlet, outlet and vent piping that have low points that could trap liquids.
No image(s) found...
2.2. Thermowells and Temperature Indicating Instruments:
S/N
Action
Observations
Observation Images
2.2.1
Inspect for signs of leakage, mechanical damage, improper installation, corrosion and or cracks in attachment welds.
No image(s) found...
2.2.2
Inspect for presence of seal welds.
No image(s) found...
2.3. Temporary Repair Clamps/Enclosures
S/N
Action
Observations
Observation Images
2.3.1
Inspect for leakage, mechanical damage, paint failure, corrosion or cracks in welds
No image(s) found...
2.4. Temporary Repair Clamps/Enclosures
S/N
Action
Observations
Observation Images
2.4.1
Inspect for leakage, mechanical damage, paint failure, corrosion or cracks in welds
No image(s) found...
VESSEL SCHEMATICS
Name of Inspectors:
Signature of Lead Inspector
No image(s) found...
Reviewed & Signed By: Date:
Save
